Paul and his crew were amazing to work with. I had them install a complete HVAC system in my new build and I couldn't be more happy with the quality of their workmanship. The crew prompt and professional and everybody was actively involved in troubleshooting any oversights in my construction plans. Their commitment to doing the job right was unparalleled. I am a custom home builder and I will use EcoFlow every chance I get!
New Construction Plumbing and Heating in Salmon Arm and the Shuswap
From the site prep work to the final finishes, we work with your contractor to get your heating, cooling, ventilation, plumbing, and gas lines in where you need them, when they're needed.
One trade instead of three
On most new builds, the plumber, the gas fitter, and the heating contractor are three different companies with three different schedules. We do all of it in-house: the furnace, heat pump, or boiler, the ductwork, air conditioning, and ventilation, the gas piping that feeds them, and the drains and water lines. That means one crew, one schedule to work around, and one number to call when something on the plans doesn't add up.
We work to your build schedule and keep the inspections lined up, so the trades behind us aren't left waiting.
Bring us in at the layout stage
The best time to call us is before the framing starts, while the plans can still change. That's when the heating and cooling can be designed with the house, instead of fitted into whatever space is left over once it's framed. A few decisions are much cheaper on paper than on site:
- Where the mechanical room goes. Close to the middle of the house means shorter duct runs and shorter waits for hot water.
- How the ducts get from the equipment to every room, before the joists and beams are in the way.
- Whether there's heat in the slab. In-floor loops have to be laid before the concrete is poured, so this decision can't wait.
- What heats the house. A heat pump, a furnace, or a boiler with in-floor radiant heat. We'll talk through what suits the house, the fuel at the lot, and your budget.
How a new build runs
- Underground. Before the slab goes in, we lay the drains, bring the water line in, and lay any in-floor heating loops.
- Rough-in. Once the house is framed, we run the water lines, drains, and vents, the gas piping, and the ductwork, before the insulation and drywall go on.
- Inspections. The plumbing is inspected before the walls close. Gas piping goes in under a gas permit and is pressure tested before anything is connected to it.
- Finish. After the drywall and flooring are done, we set the fixtures, connect the appliances, and start up and test the heating and cooling equipment.
- Handover. We show you where the main water shutoff, the gas shutoff, and the filters are, and what needs servicing and when.
Building to the Step Code
New homes in BC are built to the BC Energy Step Code, which sets how energy efficient and how airtight a house has to be. In Salmon Arm, a new house has to pass a blower door test at the level the City requires.
An airtight house changes the mechanical side of a build in two ways:
- It needs mechanical ventilation. Fresh air no longer leaks in through gaps, so it has to be brought in on purpose. A heat recovery ventilator (HRV) does that while holding on to the heat you've paid for.
- It needs less heat. An efficient house can get away with smaller equipment than the old rules of thumb would suggest, which is another reason to size the system to the house.
If you're aiming past the required step, we can talk through the heating options that fit.
Building outside town?
A lot of new homes in the Shuswap go up on acreages and rural lots, which usually means a well, a septic system, and propane instead of a natural gas line. We plumb the house and run the line from the house to the septic tank. On propane, we run the gas line from the tank to the house and connect everything inside (see natural gas or propane).
Shops, barns, and garages that aren't heated all winter need their water lines protected too. There are a few ways to do it:
- Bury it and use a frost-free hydrant. The line runs below the frost line, and the hydrant drains itself when you shut it off.
- Keep the building just above freezing with a little heat and insulation.
- Drain it for the winter. A shutoff and drain valve, where the line can't freeze, lets you empty it each fall, with plumbing antifreeze in the drains and toilet.
We'll help you pick the one that suits how you use the building.
Shops, garages, and additions
The same goes for the buildings beside the house. A new shop or garage can have in-floor heat in the slab, a gas unit heater, or a mini-split, and the gas line or water line run out to it while the trench is open.
Want to know who's coming to your door?
You can read a bit about all of our employees on our About page!
Meet the crewCommon questions
When should I call you on a new build?
As early as you can, ideally while the plans are still being drawn. The heating layout and the mechanical room are much easier to get right on paper. At the latest, call before the foundation is poured, because the drains and any in-floor heat go in first.
Will you quote from plans?
Yes. Call us or fill out our contact form first, and once we've talked, we'll have you send the plans over. We'll price the plumbing, gas, and heating from them, and if anything on the drawings won't work for the mechanical side, we'll tell you before it's built.
Do you work with owner-builders?
Yes. If it's your first build, we'll tell you what we need from you and when, so the job keeps moving.
Who arranges the inspections?
We book the inspections for our own work: the plumbing and the gas.
Does a new house need an HRV?
A new house needs mechanical ventilation, and in an airtight house an HRV is the usual way to do it. It brings in fresh air and recovers heat from the stale air going out. We'll tell you what your plans call for.
Can you put in-floor heat in the basement slab?
Yes, as long as the loops go in before the concrete is poured. See boilers and in-floor radiant heat for how it works.
Planning a build? Bring us in early.
Call us or fill out our contact form, and we'll get back to you to talk through the heating, cooling, plumbing, and gas on your new home. Once we've talked, send us the plans and we'll price them. The estimate is free.
Reach us between 8:00 and 4:00 on a weekday and you'll hear back the same day.